Home › Repair or replace › What thickness of plywood for a roof? How sheathing thickness is set

What thickness of plywood for a roof? How sheathing thickness is set

There is no single right thickness. The spacing of the rafters and the stamp on the panel decide it, and you can read both from inside the attic.

There is no one thickness of plywood for a roof. Roof sheathing thickness depends on how far apart the rafters or trusses are, and on the span rating stamped on each panel. The building code and the manufacturer's tables set the number, not a rule of thumb.

What decides the thickness

Sheathing is a floor for the roof covering. It has to span the gap between supports without sagging. Wider gaps need a thicker or stronger panel. Narrower gaps allow thinner ones.

Three things set it: the spacing of the rafters or trusses, the loads the roof must carry in your area, and the grade of the panel. Snow country asks for more than a mild climate.

How to read the stamp on the panel

Structural panels carry a grade stamp. It shows a span rating written as two numbers, such as 24/16. The first number is the maximum support spacing, in inches, when the panel is used on a roof. The second is the maximum spacing when it is used as a floor.

So a panel rated 24/16 is made for roof supports up to 24 inches apart. The stamp also names the panel type, plywood or oriented strand board (OSB), and its exposure rating.

Look from the attic, not the roof

You do not need to go up to find out what you have. From inside the attic you can often see the underside of the sheathing between the rafters. Use a flashlight, and look at the following.

  • Whether the panels are plywood or OSB.
  • Any stamp visible on the underside, which gives the span rating.
  • How far apart the rafters or trusses are.
  • Dark stains, soft spots, or edges that have swollen or delaminated.

Why thicker is not always better

A thicker panel on closely spaced rafters adds weight and nothing else. The right panel is the one rated for your spacing. Going far above that rating does not stop a leak. It is the felt, the flashing and the shingles that keep water out.

When thin or soft sheathing is a warning sign

If the roof deck feels spongy, if you see a sag between rafters, or if panels look swollen from long damp, the problem is not the thickness. It is water getting in, and that leak needs finding. See roof decking for what damaged decking looks like from below.

Do not try to judge soft decking by walking on it. Sagging or a shifting deck is a job for a licensed roofer, and a sagging frame needs a licensed structural engineer.

Questions to ask before a re-deck

  • What is the span rating of the new panels, and does it match my rafter spacing?
  • Is the old sheathing actually damaged, or only stained?
  • Can you show me photos of the bad sections?
  • Is the leak source fixed before the new deck goes on?

A good roofer answers these with specifics. Read hiring a roofer before you sign anything.

Frequently asked questions

What thickness of plywood is used for a roof?

It depends on rafter spacing and the panel's span rating. The grade stamp on the panel and your local building code set the number.

What does 24/16 on roof plywood mean?

The first number is the maximum support spacing in inches for roof use. The second is the maximum spacing for floor use.

Is thicker roof sheathing always better?

No. The right panel is the one rated for your rafter spacing and loads. Extra thickness does not stop leaks.

How can I check my roof sheathing without climbing up?

From inside the attic with a flashlight. Look at the underside for stamps, rafter spacing, stains, soft spots and swollen edges.

Is spongy or sagging roof decking a DIY job?

No. Soft decking needs a licensed roofer, and a sagging frame needs a licensed structural engineer.

Sources

What this page explains is based on these official sources. If you check one and it does not match what you read here, send it to us and the article gets corrected.

Keep reading